자유게시판>

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window can cause a lot of trouble. It could also be an opportunity to upgrade your glass to energy efficient or insulated windows to enjoy benefits such as more comfort, higher potential for resales, and less bills.

This is a project you could do yourself for a fraction of the cost of hiring an expert. You'll only require the appropriate tools and a few hours of your time.

Glass

If your single pane windows are old damaged, cracked or deteriorating replacing them with more modern insulated or tempered glass can increase energy efficiency and decrease noise while also preserving the historic integrity of older homes. Most homeowners with basic hand tools can replace the window pane. In addition to a replacement pane, the following items are required for the replacement process: latex glazing putty Glazier's points; pliers and an electric heater to warm the old putty, if needed. Wear safety goggles and gloves prior to starting. Working with broken glass can cause serious injuries.

Begin by removing any broken pieces of glass. This can be done with the help of pliers but a flathead screwdriver may be used in a pinch. Make use of a wood chisel or putty knives, to take away any remaining old putty around the frame and the window sash. Be careful to not damage the window sash. Work slowly and carefully. This is best done on an elevated ladder, not on the ground. Also, you should have someone on the ground to hold it steady.

After you've removed all the old putty, you can prepare the window frame to accommodate the new pane. To allow for seasonal expansion or contraction and contraction, subtract 1/8 inch from the measurements of the width and height. Take these measurements to an hardware store or home center and get a piece of stock glass cut to size. Alternatively, you can cut the glass yourself if you have the right tools.

After putting in the new glass Apply a small amount of caulking around the edge. This will make the glass weatherproof. Then, you can install a glazier's pointing on each side of the frame to secure the pane into the right place. The points shouldn't be so tight that they cause friction between the sash and the frame but they shouldn't be too loose.

Before applying the putty work it in a gentle manner until it's soft and free of lumps. Make it into pencil-sized strips. Place the first strip in the corner of the frame, moving from one corner to the other to ensure it is smooth and even.

Glazier's Points

The glazier's points are tiny triangular metal pieces which help to secure the glass to the frame without damaging the delicate surface. Understanding how to use these hidden tiny pieces of help is simple and can save you money on professional installation or the cost of purchasing new glass.

After the old putty and the glazier's point are gone and the frame is thoroughly cleaned with a knife to remove any remaining traces. Lightly sand the wood in the rabbet grooves, if necessary, to smooth out rough areas. If you sand wood protect it with painter's tape to prevent accidental damage.

Note down the dimensions of the frame. Take these measurements to a hardware store or home center and have the new pane made slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for Window replacement companies expansion and contraction.

Place the new pane into the frame and press it into the frame using your hand. Then use the point of your chisel, or the back of the putty knife to make a tap on the glazier's points, as shown in Figure 11. After you're done, the points should be flush with the top edge of the pane, and the shoulders that are raised of the points should be below the rabbet's rim groove.

Apply a thin layer glazing compound to the rabbet grooves as well as the edges of the new glass. This will seal and protect the edges. Allow it to dry and cure completely.

Install the new window sash once the glazing compound has dried. First, coat the wood with a thick coat of linseed oil. This will stop the new putty from sucking up the moisture and deteriorating and cracking with time. Apply the coating using a brush this coat, or the tip of the putty blade. Then, use the chisel that is on the back of the putty tool or the back of the putty handle to gently hammer the new sash or glazier's point into the grooves of the rabbet. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball thrown, a rock thrown in error, or a fallen tree could result in a broken or cracked window pane. Most windows can be replaced easily by simply putting in a fresh piece. The glass is held in place by a small metal clip, referred to as a glazier's point and putty. This compound is also known as glazing compound. Remove the old pane and Window Replacement Companies clean the area with an abrasive, scraper that is a pull type or a wood chisel. Wear gloves and safety glasses when you work. You'll need a heat gun in the event that the window is glued to the frame.

If you're planning to install the original sash, remove the molding pieces that secure the old pane. Sand the sash until it is flat and ready to receive new caulk. After the sash has been re-installed, apply a new silicone caulk around the glass to ensure that it won't leak or discolor as time passes.

Take out the glazing points in the rabbets. These are the grooves in the sash, which is where the glass is located. If they're difficult to cut, place the hand tool, such as a heating gun over them for a few minutes to soften them. When using a heating tool, make sure to avoid damaging the sash's railings and sash.

Once the old glazing points and putty have been removed, make a bed for the new pane. Roll a rope with glazing compound between your fingers, and make it around 1/2 inch thick. Then, you can press it into the rabbets where the glass will be. The glass must rest against the putty on both sides. If needed gently tap your glass into the rabbet using your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk prior pressing it into the sash. Otherwise, you'll need to putty over the crack to form an impervious seal to keep water out. Once the putty is dry clean the oily film off the glass and allow it to dry completely before painting. Paint after the putty is completely dry. It will not make a strong seal and could be leaking or discoloring over time.

Paint

You might be worried about replacing a broken pane of glass. However, replacing a single glass pane doesn't require a huge amount of money If you can do it yourself. In fact even windows with double panes can be replaced at a fraction of the cost of replacement windows uk of an expert.

If you are working with large glass windows, first make sure it is securely attached to the frame. This can be done relatively easy and fast using the proper tools and techniques.

When you're ready to start with the removal of the old window by prying out the metal glazing points that are attached to it. These are tiny metal triangles that function as "nails", holding the window within the frame. They are placed under a bead of glazing putty, which is then cured to form a solid, molded wedge that secures the window in place and conceals the window Replacement companies's points.

Once you have the old pane taken away clean the surrounding frame and wood. Scrape away any old paint and sand down the rabbet grooves, where the glazing points were. Sand them down to clean wood surfaces, so that you can paint the frames the same color. After sanding the wood, apply a layer of flax oil. This will help extend its life.

Next, measure the width of the window's opening. You'll need to determine the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get a precise size for the new pane. This will allow for seasonal changes in the glass. You can bring these measurements to a hardware store or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.